Glow-in-the-Dark Pigment Powder

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Shojin Blue is a WHITE based bright blue pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size                     35-45   μm

Ingredients                      Zinc Sulfide

Heat Threshold                752 °- 1112 °

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Daijin Blue is a blue based bright blue pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients              Strontium Aluminate, Polyurethane-11, Ultramarine Blue

Heat Threshold        752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Mizudori Green is a WHITE based bright blue pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size                     15-25   μm

Ingredients                      Zinc Sulfide

Heat Threshold                752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Asagi Green is a WHITE based green pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size                     5-10   μm

Ingredients                      Zinc Sulfide

Heat Threshold                752 °- 1112 °

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Midori Green is a Green based pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Chromium Oxide

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Daitoku Purple is a purple based bright purple violet pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Maganese Violet

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Momoiro Pink is a pink based bright pink pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients              Strontium Aluminate, Polyurethane-11, Red 28, Yellow 5

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Beni Red is a Red based pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Red 28

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR NEONS

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Daidaiiro Orange is a orange based bright orange pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Red 28, Yellow 5

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Daishin Yellow is a yellow based bright yellow green pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Yellow 5

Heat Threshold        752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com

ALWAYS TEST BEFORE FULL APPLICATION

DESCRIPTION

Orenji Orange is a orange based light orange pigment and part of our Glow Series line.

Expose the Glow in the Dark pigments to light in order to charge the pigments.

GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge.

Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow.

Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less.

Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more. 

INGREDIENTS & PARTICLE SIZE

Particle size              30-50   μm

Ingredients               Strontium Aluminate, Polyurethane-11, Yellow 6

Heat Threshold         752 °F - 1112 °F

MIXING TIPS FOR GLOW IN THE DARK

Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough.

Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown.

If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down.

Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE

ADDITIONAL DATA

NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category.

We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations. 

FDA:  Fact Sheet: Color Additives and Cosmetics

FDA:  Color Additives Permitted for Use In Cosmetics

EPOXY RATIOS

The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired.

For example:

• Are you looking for an opaque or transparent look? 
• Lighter colors may take more pigment to achieve the color.

Why micron sizes matter:

• PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle.
• Typical pigments average 10-60um. 
• Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours.
• For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster. 
• To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.

SOAPS RATIOS

  NOTE: Due to the white MP base, it will always create a pastel color.

AUTOMOTIVE / REMOVABLE PAINT RATIOS

DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure. 

ACRYLIC POURING RATIOS 

INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS

GRAPHIC INKS & SCREEN PRINTING RATIOS

COSMETICS RATIOS

FIREARMS (CERAKOTE) RATIOS

 Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base.

Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references.

• 5 grams of pigment per 4oz
• Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application.
• 3 coats for full saturation. Some colors may require less.
• Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE. 
• Recommend using a .80 spray nozzle. Some use 1.0 for clears.

REQUEST SAFETY DATA SHEET (SDS)

To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com