Rectangular Molds

FINAL CAST DIMENSIONS
Size: Approx. 4"
Depth: 1/2"

We are offering this in 7 shapes: Round, Square, 4 unique Geode shapes and Hexagon. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

This listing is for 1" Deep Rectangle Molds. There are 8 different sizes available. These molds are ULTRA Quality and Long Lasting!

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

4" X 6"
6" X 8"
8" X 10"
10" X 16"
DEPTH: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a Rectangle Flat mold. These flats are perfect for wall hangings, signs, Serving Trays, or anything else you can think of! 

Resin done by @artworkbyjennyshlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
12" x 8" x 2"
14" x 9" x 2"
16" x 6" x 2"
16" x 12" x 2"
18" x 8" x 2"
18" x 10" x 2"
18" x 12" x 2"
19" x 14" x 2"
24" x 12" x 2"
24" x 16" x 2"

This listing is for 2" Deep Rectangle Molds. These molds are ULTRA Quality and Long Lasting!

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

4" x 4" x 2"
6" x 6" x 2"
8" x 8" x 2"
10" x 10" x 2"

This listing is for 2" deep square molds.  We offer 4 different sizes.  

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 18"

Width: 7.4"

Depth: 1.25"

Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Cleaver Shaped Cheese Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Small Pill Tray: 4" x 6"
Large Pill Tray: 4" x 9"
Small Oval Tray: 4" x 6"
Large Oval Tray: 6" x 8"
Small Rectangle Tray: 4" x 6"
Large Rectangle Tray: 6" x 8"
Small Circle Tray: 5"
Large Circle Tray: 7"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

Surface Finish:  Smooth and Glossy

This listing is for our Improved Tray Molds.  We've taken the shapes that you love and made them even better. All edges of this tray will be rounded giving it a softer look.  It offers a thicker base of 3/8" plus a slightly increased rim width. This gives you extra room to work with.  These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!!  There will be no lines in your finished product from stacking acrylic.   This is an ULTRA QUALITY MOLD!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.  

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
SQUARES

3" x 3"
4" x 4"

5" x 5"
6" x 6"
8" x 8"
10" x 10"
12" x 12"

DEPTH: 3"
SURFACE FINISH: All surfaces are smooth and glossy

This listing is for 3" Deep Square Molds.  We offer this popular mold in 7 sizes.

*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. This is important to ensure your final result has straight sides.

The 3"x3" mold does not have wall stiffeners due to its small size.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

A5 Size - ~8"x6" (Large)
A6 Size - ~4"x7" (Medium)
A7 Size - ~3.5"x5" (Small)

Depth: 1/4"

This listing is for a Notebook Mold with holes for the binding rings. These Resin Notebook Cover Molds are offered in 3 sizes. A5 Binder, A6 Binder, and A7 Binder. These are all 1/4" deep which gives you more room to work with compared to the cheap ones. The holes are elongated as well to better fit the binder rings! All accessories can be found on amazon, links are below!

Binder Rings -https://amzn.to/3vnVLTm

A5 Paper - https://amzn.to/3aIDpTA
A6 Paper - https://amzn.to/3FIYn2K
A7 Paper - https://amzn.to/3p628tp

Resin work done by @artworkbyjennyshlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
4" x 4" x 1"
6" x 6" x 1"
8" x 8" x 1"
9" x 9" x 1"
10" x 10" x 1"

This listing is for 1" Deep Square Molds. These molds are ULTRA Quality and Long Lasting!

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Chunky Bowed Rectangle with dual handles Charcuterie Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 22"
Width: 6"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Large Bowed Rectangle Silicone Mold. This style has double handle holes. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Looking for a high-quality silicone mold that's perfect for creating stunning castings? Look no further than Eye Candy Silicone & Molds' 10x10x3 square silicone mold. With its precise measurements and durable silicone material, this mold is the perfect tool for all your crafting needs.

High Quality Silicone

Made of high-quality silicone, this mold ensures precise measurements and durability, allowing you to create uniform castings that are sure to impress. And with its non-stick surface, you can easily release your finished product without damaging it.

Versatile Square Mold

Its versatile square shape allows you to experiment with different designs and textures, making it perfect for all kinds of crafting projects. Whether you're a professional or a hobbyist, this mold is a must-have tool for your collection.

Elevate Your Crafting with Eye Candy's 10x10x3 Square Silicone Mold

With its easy-to-clean surface, the 10x10x3 square silicone mold is a reliable tool that you can use for many crafting projects to come. Elevate your crafting and create stunning and unique serving boards with Eye Candy Silicone & Molds' 10x10x3 square silicone mold.

Final Cast Dimensions:

Length: 24"
Width: 12"
Thickness: 2"
Surface Finish: Smooth/Glossy

This listing is for Deep Rectangle Silicone Mold. 

**This mold uses PREMIUM Silicone which is a longer lasting silicone. There is a higher tear resistance and has a higher shore hardness. The color of the PREMIUM silicone will be clear translucent.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.


Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 18"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Rectangle with Embedded Dual Handles Charcuterie Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 17"
Width: 7"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Charcuterie Board Mold with an organic handle.

Resin work and photos courtesy of @tuzzstable

his listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

RECTANGLES
4.5" x 3.5"
9" x 6"
12" x 9"
14" x 11"

DEPTH: 3"
SURFACE FINISH: All surfaces are smooth and glossy

This listing is for 3" Deep Rectangle Molds.  We offer them in 4 sizes.

*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. This is important to ensure your final result has straight sides.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 3.5"

Width" 2"

Depth: .25"

Surface Finish:  Smooth/Glossy

This listing is for a Small Rectangle Mold that can be used to make name tags, mini signs, magnets, or keychains! Each Rectangle Mold comes with 6 cavities allowing you to create more at a time.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This style charcuterie board mold has a free flow handle.

Listing video and photo courtesy of @jaredcoreyconcepts

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Photo Size: 4" x 6"
Outer Dimension: 7" x 9"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume: 67.5 in ^3 (inches cubed)

This listing is for a Picture Frame Mold. This mold is designed so you are working with your flowers face up.


*** 1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order. ***

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage. 

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Resin work and photos courtesy of @aafloralpreservation

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Length: 5"
Width: 2"

OR
Length: 7"
Width: 3"

Depth: 3/8"


This listing is for Sign Molds! These Hanging Sign Molds come in 2 different sizes and each size has 2 shapes -- Straight Sides and Curved Sides! These Wall Hanging Molds have a 3/8" depth giving you ample room to include things in your resin and giving your sign a nice thickness.

Mold idea and Resin Work by @craftycatgifts13

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

DONT TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
Make sure the resin is fully cured. Uncured resin may rip the mold.
Please follow all safety precautions when using resin. It is very toxic.
Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
If you have further questions or concerns about your mold, please shoot me a message on Etsy and Ill get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Length: 4"
Width: 4"
Thickness: 1"
Sharp Corners
Glossy/Smooth/Shiny Top + Sides

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message  and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Photo Size: 5" x 7"
Outer Dimension: 8" x 10"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume: 67.5 in ^3 (inches cubed)

This mold is designed so you are working with your flowers face up.

*** 1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order. ***

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage. 

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Resin work and photos are courtesy of @aafloralpreservation

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Size Together: 17" X 17.5" X 1.25"

Tall Half: 17" x 9"

Short Half: 13.5" x 8.5"

Depth: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Romeo & Juliet Serving Board Set Silicone Mold. This one mold will produce 2 pieces which will nest together perfectly. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 18"
Width: 5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a wine bottle shaped charcuterie mold or cheese board mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 7"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Charcuterie Board Mold. This style has the flared handle and a rectangle shaped body. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

DIMENSIONS ORIGINAL STYLE 

Sizes:

 4" x 6"
6" x 8"
8" x 10"
5" x 13"
9" x 13"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

DIMENSIONS NEW & IMPROVED STYLE

4" x 6"
6" x 8"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

This listing is for Rectangle Tray Mold. We have 5 different sizes of this tray to meet your needs. They are approximately 4" x 6", 6" x 8", 8" x 10", 5" x 13" or 9" x 13" and it's approximately 5/8" deep. The base is 1/4" thick and the walls are 3/8" thick.

We have added a new and improved version on two of our most popular trays. 4" x 6" and 6" x 8".  All edges are rounded and the base is slightly larger.  These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!!  There will be no lines in your finished product from stacking acrylic. 

*** PLEASE NOTE: The Silicone color for your mold may be different then what is pictured.  This does not affect the quality of the mold.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Height: 18"
Width: 8"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Slanted Rectangle Charcuterie Board Mold with 1 embedded handle.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Photo Size: 6" x 6"
Outer Dimension: 9" x 9"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume 1.5 thick Molds: 67.5 in ^3 (inches cubed)

This mold is designed so you are working with your flowers face up.

1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order.

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage. 

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Resin work and photos are courtesy of @aafloralpreservation

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 17"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Fishtail Charcuterie Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Small: 4"x4"
Medium: 6"x6" 
Large: 8"x8"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

This listing is for a silicone mold to create a Square tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.