Arts & Craft Molds

FINAL CAST DIMENSIONS
Size: Approx. 4"
Depth: 1/2"

We are offering this in 7 shapes: Round, Square, 4 unique Geode shapes and Hexagon. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Length: 8"
Width: 1 1/2"
Thickness: 1/8"

This listing is for a Bookmark Mold!

Please message us with any questions you may have regarding this mold.

Resin work by @artworkbyjennyshlemon

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Height: 3"
Width: 1.5"
Thickness: 1/4"

This listing is for a Tag Mold. This mold has 2 cavities

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.  

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials.  The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade.  They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Diameter: 5" - 7" - 9"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Scalloped Tray Mold.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 5"

Circle Portion: 4"

Depth: 3/8" or 1/2"

This listing is for a Round Ornament Mold. This ornament mold is a best seller! 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Length: 6.5"

Width: 6.5"

Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a Shamrock FLAT shape. 

Please note this is not a tray but is perfect for wall hangings and many other things!

Resin work and photos courtesy of @mlcresindesigns

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Length: 7"

Width: 6"

Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create an Africa shaped Flat mold. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4.5"
Width: 4.5"
Deep: .25"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Spider Web Coaster Set Mold with a stand! This set comes with 4 Spider web molds and an oval tray stand for when you want to display your coasters. 

The image on the coaster is engraved which means it will come out matte. The image will also be recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 5.5"
Width: 4"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Coaster Mold Set to create a Coffin Coaster Set with a stand. This Coffin Mold comes with 4 identical coffins in one mold and an oval tray stand with slots for when you want to display or are not using your coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 4.5”

Width: 4.5”

Depth: 1/4”

This listing is for a Star Coaster Molds. This Coaster Set Mold comes with 4 Star molds and an Oval tray stand for when you want to display your coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured.  Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message  and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Small: 5”x5”

Medium: 7”x7”

Large: 9”x9”

Depth: 3/8”

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a Weed Leaf shaped Flat mold. These flats are perfect for wall hanging decor or anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Height: 1.875”

Length: 1.875”

Deoth: 1/4”

This listing is for a silicone mold to create a Pot Leaf/Weed/Cannabis shape used for magnets, Earrings, or keychains. Each mold comes with 6 cavities allowing you to create more at a time.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Length: 7"
Width: 7"
Rim Width: 1/2"
Rim Height: 1/2"
Base Height: 1"
Overall Height: 1.5"
All Edges Rounded
Glossy Finish

This listing is for a mold to create a Deep Paw Print tray. This mold could work well as a remembrance mold of a favorite pet. It offers room for a collar, pet tag or fur.

All edges of this tray are rounded giving it a softer look.  You will have up to 1" of working room underneath the face of the tray.  Our Deep Paw Print Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Out!!  There will be no lines in your finished product.   Free Layout Template Included.

Resin work and photo credit goes @mlcresindesigns

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.  

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Tall: 4.5"
Length: 2"
Width: 1"
Super Glossy Finish - High Quality

This listing is for an Elephant Ring Holder Mold. 

Please note the elephant mold comes with one split down the side for easy demolding. The splits are easy to seal. Use the rubber bands supplied to align and seal the split before pouring your resin.

This listing is for the silicone mold ONLY.

Please message us with any questions you may have regarding this mold.

Black Elephant Resin Piece done by @craftycatgifts13

Clear Resin Piece done by @Mishy1971

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 2”

Width: 1.25”

Depth: .25”

This listing is for a bat silicone mold. These are a perfect size for hair clips, keychains or magnets. Each mold comes with 4 cavities allowing you to create more at a time.

These bats fit perfectly on our mini hair clips that we offer.


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

3.25” Diameter

1.25” Deep

This listing is for a business card holder mold. It is a faceted mold. 

Resin work and photos by @mlcresindesigns

Please message us with any questions you may have regarding this mold.

This is a deep mold so please review your specific resin "max pour depths" to avoid exothermic reactions which will shorten the lifespan of your mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSION

SIZE: 1 3/4"
DEPTH: 1/4"

This listing is for a Geode Mold. This can be used as a Geode Keychain Mold, Magnet Mold or Earring Mold. Each mold comes with 6 cavities allowing you to create more at a time.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Length: 7.5"
Width: 4.5"
Rim Width: 1/2"
Rim Height: 1/2"
Base Height: 1"
Overall Height: 1.5"
All Edges Rounded


This listing is for a Deep Pill Tray Mold. All edges of this tray will be rounded giving it a softer look. You will have up to 1" of working room underneath the face of the tray. This gives you plenty of room for your florals or any other inclusion you would like to add. Our Deep Pill Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!! There will be no lines in your finished product. 

Resin Work and Photos by @kanetahale

Free Layout Template Included

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message  and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
4" TALL CROSS:  4" x 2.25" x 5/8" Cavity Width; 3/4" Thick
6" TALL CROSS:  6" x 3.25" x 1" Cavity Width; 1.25" Thick
9" TALL CROSS:  9" x 4 7/8" x 1.5" Cavity Width; 1.25" Thick
13" TALL CROSS: 13" x 7" x 1.5" Cavity Width; 1.25" Thick
20" TALL CROSS: 20" X 10" X 2.5" Cavity Width; 1.25" Thick

Surface Finish: Smooth/Shiny/Glossy

This listing is for a Deep Cross Silicone Mold. We are offering this mold in 5 sizes to meet all your needs. 

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.


Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 5.5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a shiny silicone mold to create a Tree shaped Coaster Set with a stand! This set comes with 4 Tree Coaster molds and an Oval tray stand for when you want to display your coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 9"
Width:9"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Spiderweb Tray Mold  

The image on this tray is engraved which means it will come out matte. The image will also be slightly recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Snowflake Coaster Set with a stand! This set comes with 4 snowflake molds and an Oval tray stand for when you want to display your coasters. The snowflakes come in two different styles so all four aren't the same.

The image on this tray is engraved which means it will come out matte. The image will also be recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a Skull Mold. This 3D Skull Mold is currently available in 3 sizes. 

-2" Long
-3" Long
-4” Long


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Solid Round Ornament: 3.25" in diameter
Donut Ornament: 3 1/8" in diameter
Cavity Width: 3/4"
Center Hole Size: 1 3/4"
Depth: 3/4" Deep for Both Molds
Finish: Glossy/Shiny

This listing is for a Round Ornament Molds. We are offering this mold in 2 styles. The first is a solid round ornament and the second is a flat donut shaped ornament.
Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Diameter: 5", 7" or 9"

Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a shiny silicone mold to create a Circle shaped Flat mold. These circle flats are great for multiple uses -- wall hangings and decor or put your favorite inspirational saying on it. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

DIMENSIONS ORIGINAL STYLE 

Sizes:

 4" x 6"
6" x 8"
8" x 10"
5" x 13"
9" x 13"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

DIMENSIONS NEW & IMPROVED STYLE

4" x 6"
6" x 8"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

This listing is for Rectangle Tray Mold. We have 5 different sizes of this tray to meet your needs. They are approximately 4" x 6", 6" x 8", 8" x 10", 5" x 13" or 9" x 13" and it's approximately 5/8" deep. The base is 1/4" thick and the walls are 3/8" thick.

We have added a new and improved version on two of our most popular trays. 4" x 6" and 6" x 8".  All edges are rounded and the base is slightly larger.  These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!!  There will be no lines in your finished product from stacking acrylic. 

*** PLEASE NOTE: The Silicone color for your mold may be different then what is pictured.  This does not affect the quality of the mold.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

4" X 6"
6" X 8"
8" X 10"
10" X 16"
DEPTH: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a Rectangle Flat mold. These flats are perfect for wall hangings, signs, Serving Trays, or anything else you can think of! 

Resin done by @artworkbyjennyshlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Tall Pumpkin: Approx. 2.5" in diameter and 4" tall
Short Pumpkin: Approx. 3.75" in diameter and 2" tall
Mini Pumpkin: Approx. 1.5" in diameter and 1.5" tall.
Flat Keychain Pumpkin: Approx. 2 1/4" x 2", 1/4" deep

This listing is for an assortment of pumpkin molds. All have a shiny, glossy finish.

The bigger pumpkins are DEEP molds. Please check your resin's maximum thickness to avoid an exothermic reaction.

Resin work done by @mlcresindesigns

This listing is for the silicone mold ONLY.

Please message us with any questions you may have regarding this mold.


All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4"
Width: 5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a shiny silicone mold to create a Weed Leaf Coaster Set with a stand. This set comes with 4 Weed Leaf Cavities in 1 mold and an oval tray stand with slots for when you want to display or are not using your coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

DIMENSIONS REGULAR VERSION

Small Pill Tray: 3.5" x 7"
Large Pill Tray: 3.5" x 9"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

DIMENSIONS ROUNDED EDGES/SMOOTH SIDES
Small Pill Tray: 4" x 6"
Large Pill Tray: 4" x 9"
Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

This listing is for an ULTRA QUALITY Pill Tray Silicone Mold. We offer this Pill Tray Mold in 2 sizes, 3.5" x 7" or 3.5" x 9" and it's approximately 5/8" deep.  The base is 1/4" thick and the walls are 3/8" thick.  What makes our Pill Tray Mold different from all the others?  Our Pill Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!!  There will be no lines in your finished product.  

We have added a new and improved version on our most popular trays. All edges are rounded, the base is slightly larger, and the width is 1/2" wider. These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!! There will be no lines in your finished product from stacking acrylic.

*** PLEASE NOTE: The color of silicone used for your mold may vary from what is shown. It will be of the same high quality that you have come to expect.

Resin Work done by @artworkbyjennyshlemon and @atomcreatives

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.  

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 7"
Width: 7"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a shiny silicone mold to create a Dog/Cat Paw Print shaped tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

DIMENSIONS - ORIGINAL VERSION

Small: 4" x 6"
Medium: 6" x 8"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

DIMENSIONS ROUNDED EDGES/SMOOTH SIDES

Small: 4" x 6"
Medium: 6" x 8"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

This listing is for a silicone mold to create an oval shaped tray. 

We have added a new, more rounded version on our most popular trays. 4" x 6" and 6" x 8".  All edges are rounded and the base is slightly larger. These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!! There will be no lines in your finished product from stacking acrylic.

*** PLEASE NOTE: The color of silicone used for your mold may vary from what is shown.  It will be of the same high quality that you have come to expect.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. Original Version Tray Molds are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 5"

Circle Portion: 4"

Depth: 3/8" 

This listing is for a wide variety of Ornament Silicone Molds! There are 11 unique Christmas phrases creatively etched on these ornaments. Choose the ones you like or buy all 11 at a nice discount. 
We offer the following phrases on the ornaments:

(A) Tis The Season to be Jolly
(B) Peace on Earth
(C) Merry and Bright
(D) Home Sweet Home
(E) Merry Christmas Y'All
(F) Believe in the Magic of Christmas
(G) Deck the Halls
(H) Meet Me Under the Mistletoe
(I) Have Yourself A Merry Little Christmas
(J) It's The Most Wonderful Time of the Year
(K)Joy to the World


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 5"

Width: Varies with ornament

Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for Christmas Ornament Molds for Resin! We offer 8 different Ornament Mold shapes. You may buy them as a set or individually. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Mushroom Coaster Set! This set comes with a 4 cavity Mushroom molds. This set does not come with a stand to display the coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

SHAPE & FINAL CAST DIMENSIONS

* Coffin - 3 1/2" x 2 1/8"
* Butterfly - 3 1/2" x 5"
* Heart - 3 1/2" x 2 1/2"
* Moon - 3 1/2" x 2 1/4"
* Oval - 3 1/2" x 2 3/4"
* Star - 3 1/2" x 3 1/2"
* Weed - 3 1/2" x 3 1/2

Rim Height: 1/4"

This listing is for Mini Tray Molds. We are offering these molds in 7 popular shapes. These molds are extremely durable and will give you a resin piece that is shiny/glossy.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Small:  5"x6"
Medium: 7"x8"  
Large: 9" x 10.5"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

Surface Finish: Smooth/Shiny/Glossy

This listing is for a Heart Tray Mold. This Heart Mold comes in three sizes.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 5"
Width: 5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Ghost Coaster Mold Set with a stand (AKA Ghosters)! This set comes with 4 ghost molds and an oval tray stand with slots for when you want to display or are not using your coasters. The ghosts come in two different styles so all four aren't the same. 

The image on this coaster is engraved which means it will come out matte. Which is the 2 eyes and mouth on the ghost. The image will also be recessed into your resin piece upon de-molding which will allow you to paint it or leave it be.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 7"
Width: 2"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Comb Mold. This Hair Comb Mold produces a piece that is 7" long, 2" wide and 1/4" deep.


Mold Collab and Resin pieces done by/with @ArtworkbyJennyShlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4 1/8"
Width: 4 5/8"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a silicone mold to create a Heart Coaster Set with a stand! This set comes with 4 Heart coaster molds and an Oval tray stand for when you want to display your coasters. This comes in 2 molds. One for the 4 coasters and one for the stand.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

4" X 6"
6" X 8"
10" X 16"
DEPTH: 3/8"


This listing is for a silicone mold to create a Geode Rectangle Flat mold. We offer the 3/8" depth in 3 different sizes. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured.  Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 7"
Width: 7" when assembled
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a silicone mold to create an Easel Stand. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 4.75"
Width: 2.75"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Butterfly Coaster Mold! This set comes with 4 Butterfly molds. This set does come with a stand to display the coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Shamrock shaped Coaster Set with a stand! This set comes with 4 Shamrock coaster molds and an Oval tray stand for when you want to display your coasters. This comes in 2 molds. One for the 4 coasters and one for the stand.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Size: 7"x7"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

This listing is for a silicone mold to create a Shamrock shaped tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 10"
Width: 6"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Bat Tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Small: 5”x3”

Large: 10” x 6”

Depth: 3/8”

This listing is for Bat Flat Molds.  These flats are perfect for wall hangings, home decor or anything else you can think of!


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4"
Width: 4"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a silicone mold to create a Africa shaped Coaster Set! The size of the coasters is approximately 4" by 4". This set comes with 4 Africa molds. This set does not come with a stand to display the coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Small: 5.5”x4.5”

Medium: 7.5”x6”

Large: 9.5”x7.5”

Depth: 3/8”

This listing is for a silicone mold to create an Egg FLAT shape. 

Please note this is not a tray but is perfect for wall hangings and many other things!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 
Small: 5" X 5"
Medium: 7" X 7"
Large: 9" X 9"
Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a Mushroom Flat mold. These flats are perfect for wall hangings, sun catchers or anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 7”

Width: 5”

Depth: 3/8”

This listing is for a Mitten Flat Mold. These flats are perfect for wall hangings, home decor for winter and Christmas or anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured.  Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 7"

Width: 5.5"

Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a Gingerbread Man Mold. This flat has etchings to show his face and other markings on the body. These flats are perfect for wall hangings, home decor for winter and Christmas or anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Small: 4" x 7" 
Medium: 5" x 9"
Depth: 3/8"

Surface Finish: Smooth/Glossy

This listing is for a silicone mold to create a coffin flat. These flats are perfect for wall hangings, home decor, Halloween or anything else you can think of!


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Puffy Cloud Shape: 6"x9"

Flat Bottom Cloud Shape: 5"x9"

Depth:  3/8"

Surface Finish:  Smooth/Glossy

This listing is for a silicone mold to create a Cloud shaped Flat mold. These flats are perfect for wall hangings anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

DIMENSIONS:

Medium: 6" x 8"
Large: 8" x 10"
Depth: 3/8"

This listing is for a silicone mold to create a Moon Flat mold. These flats are perfect for wall hangings anything else you can think of!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSION

Length: 2.7"

Width: Varies

Depth: 1/4"

Surface Finish: Smooth/Glossy

This listing is for a Hair Clip Mold. We offer this mold in 6 different styles:

* Solid Teardrop
* Teardrop with Center Cutout
* Scalloped Teardrop with Center Cutout
* Solid Rectangle
* Rectangle with Center Cutout
* Bar

Each mold will have 4 of the same design on them.  You will use the resin pieces created from this mold and attach it to a metal hair clip. Giving the top of the clip a beautiful design, which will be shown beautifully in hair.

Gold hair clips CAN BE PURCHASED for $.50 Each! We have three different styles that will work perfectly with the molds!

Mold Collab and Resin pieces done by/with @ArtworkbyJennyShlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.