3d Molds

Final Cast Dimensions:
Length: 7"
Width: 7" when assembled
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a silicone mold to create an Easel Stand. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Tall: 4.5"
Length: 2"
Width: 1"
Super Glossy Finish - High Quality

This listing is for an Elephant Ring Holder Mold. 

Please note the elephant mold comes with one split down the side for easy demolding. The splits are easy to seal. Use the rubber bands supplied to align and seal the split before pouring your resin.

This listing is for the silicone mold ONLY.

Please message us with any questions you may have regarding this mold.

Black Elephant Resin Piece done by @craftycatgifts13

Clear Resin Piece done by @Mishy1971

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 4”

Width: 3”

Deep: 3/4”

This listing is for a rectangle mold to create a beautiful rectangle shaped resin dish with angled corners. PLEASE NOTE: The rooster shown on the dish is lightly etched on the mold. Other crafters say that it isn't noticeable on your finished piece.


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSION:

Diameter: 1.6"

Bottom Opening: .93"

Surface Finish: Glossy

This listing is for a Sphere Wine Topper Mold. 

Silicone color may vary.

This listing is for the silicone mold ONLY. 

Please message us with any questions you may have regarding this mold.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSION:

Diameter: 1.5"

Surface Finish: Glossy

This listing is for a Faceted Wine Topper Mold. 
The flat bottom for attaching to the wine stopper piece is 3/4". 

Silicone color may vary.

Resin Work and Photos by @bupp_woodworks

This listing is for the silicone mold ONLY. 

Please message us with any questions you may have regarding this mold.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
Sitting Cat: 2" Tall, 1.25" Long, 1" Wide
Tiny Sleeping Cat: .5" Tall, 1" Long, .5" Wide
Large Sleeping Cat: 1" Tall, 2" Long, 1 3/4" Wide

This listing is for a Cat Mold. We offer this 3D Cat Mold in 3 Styles.

The sitting cat mold comes presplit to aid in demolding of your resin piece. Use the rubber band provided to align and seal the split before pouring your resin.

This listing is for the silicone mold ONLY. 

Please message us with any questions you may have regarding this mold.

Resin work: @Artworkbyjennyshlemon

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

BUNNY FINAL CAST DIMENSIONS

Tall: 2.5" x 1.25" x 1"

MUSHROOM FINAL CAST DIMENSIONS (contains 1 each of the following)

TINY MUJSHROOM: 1.25" X 3/4"

MEDIUM MUSHROOM: 1.75" X 1.25"

EGG FINAL CAST DIMENSIONS (contains 3 eggs):

Height: 1.25"

Width: 1"

CHICK FINAL CAST DIMENSIONS (contains 1 each of the following):

Short: 1"x1.5"x1"

Tall: 1.25"x1.5"x1"

Surface Finish:  Smooth/Glossy

This listing is for 4 silicone molds to create 8 individual pieces for resin. The collection contains 1 Bunny Mold, 1 Egg Mold with 3 cavities, 1 Mushroom Mold with 2 cavities and 1 Chick Mold with 2 cavities.

Please Note that only the Mushroom Mold comes presplit to aid in demolding of your piece. All other molds do not have a split.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.


SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Small:  1/2" Tall and 1" Wide
Medium: 1" Tall and 1.5" Wide
Large: Approx. 2" Tall and 1" Wide
Sitting Dog XL: 3.25" Long x 2" Wide x 3.5" Tall
Laying Down Dog XL: 4" Long x 2" Wide x 1.5" Tall

This listing is for 3D Dog Molds.  They come in a variety of shapes.  The XL sizes would be perfect for memorial or remembrance pieces as they are large enough to include fur or other items.

Please note the Medium, Large and Sitting Dog XL Sized mold comes with a split down the side for easy demolding.  Use the rubber bands supplied to align and seal the split before pouring your resin.

Resin work done by @mlcresindesigns

Please message us with any questions you may have regarding this mold.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.


SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Tall Pumpkin: Approx. 2.5" in diameter and 4" tall
Short Pumpkin: Approx. 3.75" in diameter and 2" tall
Mini Pumpkin: Approx. 1.5" in diameter and 1.5" tall.
Flat Keychain Pumpkin: Approx. 2 1/4" x 2", 1/4" deep

This listing is for an assortment of pumpkin molds. All have a shiny, glossy finish.

The bigger pumpkins are DEEP molds. Please check your resin's maximum thickness to avoid an exothermic reaction.

Resin work done by @mlcresindesigns

This listing is for the silicone mold ONLY.

Please message us with any questions you may have regarding this mold.


All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Small: 1.75” x 1” x 1.25”

Medium: 2.75” x 1.75” x 2.5”

Large: 3” x 2” x 2.75”

This listing is for a Bunny Mold. 

The medium and large bunny molds come with 2 splits to aid in demolding of your resin piece. Use the rubber bands provided to align and seal the splits before pouring your resin.

This listing is for the silicone mold ONLY. The bunny is shown in the picture only to give you an idea of the finished piece.


Please message us with any questions you may have regarding this mold.


All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

3.25” Diameter

1.25” Deep

This listing is for a business card holder mold. It is a faceted mold. 

Resin work and photos by @mlcresindesigns

Please message us with any questions you may have regarding this mold.

This is a deep mold so please review your specific resin "max pour depths" to avoid exothermic reactions which will shorten the lifespan of your mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Firefighter Symbol - Maltese Cross Mold
Height: 12"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

EMT/EMS Ambulance Symbol Mold - The "Star of Life"
Height: 12"
Width: 12.1"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Police Badge Mold
Height: 12"
Width: 9.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

Honor our heroes with these First Responder Silicone Molds, available in 3 designs:  Firefighter Maltese Cross, EMS Star of Life, and Police Badge. Perfect for resin art, memorial pieces, or heartfelt gifts that show pride and respect for those who serve.

Please note these molds are sold individually, Not as a set.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a Skull Mold. This 3D Skull Mold is currently available in 3 sizes. 

-2" Long
-3" Long
-4” Long


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 1.25"

Width: 1"

Surface Finish:  Smooth/Glossy

This listing is for Egg Molds for Resin. One mold contains cavities to create 3 eggs. Egg shapes are not exactly the same but extremely similar.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.


SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

SMALL ROUNDED GHOST: 1 3/4" Tall by 1 1/2" Wide
LARGE ROUNDED GHOST: 2 1/2" Tall by 2" Wide
TALL GHOST: 3" Tall by 1" wide
SHORT GHOST: 1 3/4" Tall by 1 1/4" Wide

This listing is for Ghost Molds for Resin. These are available in 3 styles. All ghosts have the eyes etched in them. These ghosts are a perfect addition to your Halloween decor.

The New Rounded Ghosts do not have a split. The Tall Ghost also does not have a split. (It used to but not any more :) They are easy to demold.

The Short ghost mold come presplit for easy demolding of your resin piece. Use the rubber band provided to aid in sealing the split before pouring.


Please message us with any questions you may have regarding this mold.

Resin work: @Artworkbyjennyshlemon

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Diameter: 4"

Depth: 2"

Surface Finish: Glossy and Faceted

This listing is for a Tealight Candle Holder Mold. 

This is a deep mold, please review your resin max pour depth to avoid exothermic reactions.

Resin work and Photos courtesy of @flofloflowery

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Dog Laying Down: 4" Long x 2" Wide x 1.5" Tall
Dog Sitting:  3.25" Long x 1.75" Wide x 3.5" Tall
Cat: 3.5" Long x 2"  Wide x 2.5" Tall  
Horse: 4" Long x 2.25" Wide x 2.75" Tall
Pig: 3.75" Long x 1.75" Wide x 2.75" Tall
Frog: 3.75" Long x 3.75" Wide x 1.75" Tall
Mouse: 3" Long x 2" Wide x 2.75" Tall
Bear: 2.25" Long x 2.25" Wide x 3.25" Tall
Bunny Laying Down: 4.25" Long x 1.75" Wide x 1.5" Tall

This listing is for silicone molds to make a variety of animals. These molds are roomy enough to use as a memorial mold.

The Horse and Sitting Dog Molds come presplit to aid in demolding of your resin piece.  Use the rubber band provided to align and seal the split before pouring your resin.

This listing is for the silicone mold ONLY.  

Please message us with any questions you may have regarding this mold.

All molds are handmade and inspected before shipping. 


Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fareheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All 3D molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

SMALL:
Height:  6"
Width:  5.75"
Depth: 1.25"

LARGE:
Height:  9"
Width:  8.5"
Depth: 1.25"

SURFACE FINISH:  Smooth/Glossy/Shiny

This listing is for an Angel Silicone Mold.  We offer this mold in 2 sizes - 6" and 9". 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.


Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:
Height: 13"
Width: 8.5"
Depth: 1.25"
Finish: Glossy/Shiny

This listing is for a Cancer Awareness Ribbon Mold.  Cancer ribbons are meant to show support for individuals with cancer. This piece would make great wall decor or wall hanging.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 7"
Width: 2"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Comb Mold. This Hair Comb Mold produces a piece that is 7" long, 2" wide and 1/4" deep.


Mold Collab and Resin pieces done by/with @ArtworkbyJennyShlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Length: 6"
Width: 1"
Height: 1"
Surface Finish: Smooth/Shiny/Glossy

SAFE FOR USE IN PRESSURE POT

This listing is for a Pen Blank Silicone Mold. The size of the blank is 6"x1"x1". This Pen Blank Mold comes with 5 cavities.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

DONT TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
Make sure the resin is full cured. Uncured resin may rip the mold.
Please follow all safety precautions when using resin. It is very toxic.
If you have further questions or concerns about your mold, please shoot me a message and I'll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Small: 5.1" x 4.1" x 2"
Medium: 6" x 5.3" x 2.3"
Large: 8" x 6" x 2.3"

This listing is for a Deep Standing Gem Mold with faceted sides.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Short: 1"x1.5"x1"

Tall: 1.25"x1.5"x1"

Surface Finish:  Smooth/Glossy

This listing is for Chick Molds for Resin. This mold will give you 1 each of the short and tall chicks.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.


SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FLORAL PRESERVATION MOLD

FINAL CAST DIMENSIONS:
3" DEEP
Height: 8.5" 
Width: 12"

2" DEEP
Height: 6.4" 
Width: 9"

Deep Butterfly Silicone Mold – 2 Sizes & Depths

Capture beauty and memories with our premium Deep Butterfly Silicone Mold. Designed with smooth, glossy interiors for flawless casts, this mold is perfect for floral preservation, memorial pieces, keepsakes, or any resin art project where detail and depth matter.

Resin work and photo by @thelongyardwhimsy

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FLORAL PRESERVATION MOLDS

Final Cast Dimensions:
Tall: 5", 10"
Width: 10", 5"
Depth: 3"

Surface Finish: Glossy/Smooth

This listing is for Deep Standing Oval Molds. These molds come in 2 styles. Vertical Standing or Horizontal Standing. 

This was a collaboration with @HandandHalo
Resin work and photos by @mlcresindesigns for horizontal piece and by @ivorycoledesigns for the vertical piece

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

SMALL:

HEIGHT: 4.7"

WIDTH: 6"

FLAT BOTTOM: 1.7"

MEDIUM:

HEIGHT: 6.2"

WIDTH: 8"

FLAT BOTTOM: 2.25"

DEPTH FOR BOTH: 3"

SURFACE FINISH: Smooth, Glossy, Shiny

This listing is for a Deep Standing Heart Mold. This mold has a small flat bottom portion allowing this heart to stand straight up.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
ROUNDED STYLE
Small: 4" x 5"
Medium: 5" x 7"
Large: 7" x 9"
All 3" Deep

Surface Finish: Glossy/Smooth/Shiny Top and Sides


This listing is for Deep Rounded Bookend Molds. This shape is more rounded than our other Bookend Molds giving you more space to work with. 

*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. This is important to ensure your final result has straight sides.
Free Template included for easy layout of your design!!


Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
SMALL: 4" X 8"
LARGE: 5.5" X 11
Depth: 3"

SURFACE FINISH:  Smooth/Glossy/Shiny
This listing is for a Deep Rainbow Mold. We offer this mold in 2 Sizes! 

"This shape can represent so many things. It's for the mother who gives birth to her rainbow baby, for the newlyweds embarking on this journey called marriage, for the widow remembering her lifelong love. Whatever your memory, we are here to help you preserve it." @madetoloveva

This mold is from a collaboration with @madetoloveva. All resin work shown was done by them.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

SMALL:

HEIGHT: 5"
WIDTH: 5.6"

MEDIUM:
HEIGHT: 7"
WIDTH: 7.9"

LARGE:
HEIGHT: 9"
WIDTH: 10.1"

DEPTH: All Sizes are 3" Deep
SURFACE FINISH; Smooth, Shiny, Glossy

This listing is for a Deep Heart Mold.  We offer this shape in 3 sizes.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
ORIGINAL STYLE
Small: 4" x 5"
Medium: 5" x 7"
Large: 7" x 9"
All 3" Deep

Surface Finish: Glossy/Smooth/Shiny Top and Sides


*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. This is important to ensure your final result has straight sides.

This listing is for a Deep Bookend Molds. We offer them in 3 sizes.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FLORAL PRESERVATION MOLD

FINAL CAST DIMENSIONS:
Height: 6"
Width: Varies on each individual letter
Depth: 2"
Surface Finish: Smooth/Shiny/Glossy

This listing is for Alphabet Letter Silicone Molds. The Letter "I" has cross bars at the top and bottom. The letters "P" and "F" are designed to be able to stand on their own. 

With our letter molds, you are able to work with your flowers face up.

Resin work and photos courtesy of @bupp_woodworks

Please message us with any questions you may have regarding this mold.


All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FLORAL PRESERVATION MOLDS

FINAL CAST DIMENSIONS:
Height: 9"
Width: Varies on each individual letter
Depth: 3"
Surface Finish: Smooth/Shiny/Glossy

LETTERS "F" AND "P" HAVE BEEN REVISED SO THAT THEY STAND ON THEIR OWN.

With our letter molds, you are able to work with your flowers face up.

*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. All MAIN straight sides of the letters will have embedded supports. For example: "A" will only come with stiffeners on the two long outside walls. "B" will only have it along the long straight wall on the left. "C" will have none due to it being curved, etc...

Resin work and photos by @ivorycoledesigns
Listing video by @flower_preserve

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.