Specialty Molds

(4)

From $20.00

Final Cast Dimensions:
4" TALL CROSS: 4" x 2.25" x 5/8" Cavity Width; 3/4" Thick
6" TALL CROSS: 6" x 3.25" x 1" Cavity Width; 1.25" Thick
9" TALL CROSS: 9" x 4 7/8" x 1.5" Cavity Width; 1.25" Thick
13" TALL CROSS: 13" x 7" x 1.5" Cavity Width; 1.25" Thick
20" TALL CROSS: 20" X 10" X 2.5" Cavity Width; 1.25" Thick

Surface Finish: Smooth/Shiny/Glossy

This listing is for a Deep Cross Silicone Mold. We are offering this mold in 5 sizes to meet all your needs.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Easel Stand Silicone Mold for Resin | 7" x7" |

(2)

$27.00

Rectangle Mold | 4”x 3” | Jewelry Dish Mold

(0)

$22.00

Sphere Wine Stopper Top Mold, Wine Stopper Top Mold

(0)

$20.00

Wine Stopper Top Mold, Faceted Wine Stopper Top Mold

(1)

$20.00

Paper Weight Molds | 9 Shapes | Baby Molds, Pocket Collection Molds

(1)

$30.00

Eye Candy Sample Tile Mold — 4" × 6" × 1/4" (with Embedded Logo)

(1)

~~$20.00~~ $18.00

Bookmark Silicone Mold | 8" x 1.5" |

(0)

From $9.00

18"x 7.4" x 1.25" Cleaver Cheese Board Silicone Mold, Charcuterie Board Mold

(1)

From $25.00

Final Cast Dimensions:
Length: 18"

Width: 7.4"

Depth: 1.25"

Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Cleaver Shaped Cheese Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Tray Molds | Rounded Edges | Pill Tray Mold, Oval Tray Mold, Circle Tray Mold, Rectangle Tray Mold

(0)

From $30.00

FINAL CAST DIMENSIONS:

Small Pill Tray: 4" x 6"
Large Pill Tray: 4" x 9"
Small Oval Tray: 4" x 6"
Large Oval Tray: 6" x 8"
Small Rectangle Tray: 4" x 6"
Large Rectangle Tray: 6" x 8"
Small Circle Tray: 5"
Large Circle Tray: 7"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

Surface Finish: Smooth and Glossy

This listing is for our Improved Tray Molds. We've taken the shapes that you love and made them even better. All edges of this tray will be rounded giving it a softer look. It offers a thicker base of 3/8" plus a slightly increased rim width. This gives you extra room to work with. These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!! There will be no lines in your finished product from stacking acrylic. This is an ULTRA QUALITY MOLD!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Notebook Mold | 3 Sizes, A5, A6, A7 |

(1)

From $19.00

FINAL CAST DIMENSIONS

A5 Size - ~8"x6" (Large)
A6 Size - ~4"x7" (Medium)
A7 Size - ~3.5"x5" (Small)

Depth: 1/4"

This listing is for a Notebook Mold with holes for the binding rings. These Resin Notebook Cover Molds are offered in 3 sizes. A5 Binder, A6 Binder, and A7 Binder. These are all 1/4" deep which gives you more room to work with compared to the cheap ones. The holes are elongated as well to better fit the binder rings! All accessories can be found on amazon, links are below!

Binder Rings -https://amzn.to/3vnVLTm

A5 Paper - https://amzn.to/3aIDpTA
A6 Paper - https://amzn.to/3FIYn2K
A7 Paper - https://amzn.to/3p628tp

Resin work done by @artworkbyjennyshlemon

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Organizer Dish with 2 Dividers Silicone Mold | 6" x 2.5" |

(0)

$32.99

Round Ornament Mold | 3/8" or 1/2" | Ornament Mold

(0)

From $12.50

Bunny Mold, Rabbit Mold | 3 Sizes |

(0)

From $20.00

FINAL CAST DIMENSIONS

Small: 1.75” x 1” x 1.25”

Medium: 2.75” x 1.75” x 2.5”

Large: 3” x 2” x 2.75”

This listing is for a Bunny Mold.

The medium and large bunny molds come with 2 splits to aid in demolding of your resin piece. Use the rubber bands provided to align and seal the splits before pouring your resin.

This listing is for the silicone mold ONLY. The bunny is shown in the picture only to give you an idea of the finished piece.

Please message us with any questions you may have regarding this mold.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Business Card Holder Mold, Card Holder Mold

(0)

$33.00

17" X 14" x 1.25" Romeo & Juliet Nesting Heart Serving Board Set Silicone Mold - Nesting Charcuterie Mold

(1)

From $25.00

Final Cast Dimensions:

Size Together: 17" X 14" X 1.25"

Tall Half: 17" x 6.5"

Short Half: 14.6" x 7.5"

Depth: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Romeo & Juliet Serving Board Set Silicone Mold that has a cutout heart in the center of it. This one mold will produce 2 pieces which will nest together perfectly.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Alphabet Mold | 1.5" Tall, Full Reverse | Uppercase Alphabet Mold, Keychain Mold, Magnet Mold

(0)

From $7.50

DIMENSIONS:
TALL: 1 1/2"
WIDTH: Varied Per Letter
DEEP: 3/8"
CAVITIES PER MOLD: 4

This listing is for an Uppercase Alphabet Mold. Each letter is sold separately and in a grouping of 4 of the same letter. This is perfect when you need to produce a lot for your business. These molds are great for keychains, magnets or anything else. You may notice that the letters are reversed in the mold, this is because when you demold them you want them to face the right way, with the shiny smooth side as the front.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Geode FLAT Silicone Mold | 3 Sizes |

(0)

From $22.00

First Responder Mold | 12" Tall | Firefighter Maltese Cross Mold, EMT/EMS Mold, Police Badge Mold

(0)

From $25.00

Final Cast Dimensions:

Firefighter Symbol - Maltese Cross Mold
Height: 12"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

EMT/EMS Ambulance Symbol Mold - The "Star of Life"
Height: 12"
Width: 12.1"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Police Badge Mold
Height: 12"
Width: 9.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

Honor our heroes with these First Responder Silicone Molds, available in 3 designs: Firefighter Maltese Cross, EMS Star of Life, and Police Badge. Perfect for resin art, memorial pieces, or heartfelt gifts that show pride and respect for those who serve.

Please note these molds are sold individually, Not as a set.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Skull Mold for Resin |2”, 3”, 4” | Spooky Mold, Halloween Mold

(0)

From $25.00

14.5" x 14.5" x .75" Chess Board Mold and Chess Piece Set Mold

(0)

From $50.00

Final Cast Dimensions:

CHESSBOARD:
Length: 14.5"
Width: 14.5"
Overall Depth: .75"
Outside Border Width: 3/8"
Surface Finish: Smooth/Shiny/Glossy

INDIVIDUAL SQUARES
Height: 1.5"
Width: 1.5"
Depth: .25"
Border Between Squares: .2"

CHESS PIECES
King (Slanted Rectangle): 3.5" x 1" x 1"
Queen (Pointed Rectangle): 3.5" x 1" x 1"
Bishop (Cone): 2 3/4" x 7/8"
Knight (Cylinder): 3" x 1"
Rook (Octagon): 2 3/8" x 7/8"
Pawn (Cone): 2 3/4" x 7/8"
Surface Finish: Smooth/Shiny/Glossy

Chess Piece Set

1 Chess piece set will make 16 pieces or half the amount for a full board. You can purchase 1 chess piece set and reuse the mold or purchase 2 which allows you to make all the pieces at once.

This chessboard mold measures approximately 14.5" × 14.5" × .75" overall and produces a finished board with a total thickness of 3/4". Each full-size square is 1.5" × 1.5" and is recessed to a depth of 0.25".

The board layout features 1.5" squares divided by .2" wide grid lines, all set at a 0.25" depth. This design makes it easy to cast bold, substantial squares using alternating colors of resin. After the individual squares have cured, a final backing pour can be added to lock everything together, forming the solid base of the board. The resulting cast piece finishes at a full 3/4" thick.

After demolding, you have several finishing options: leave the grid lines as-is, fill them with a contrasting material, or sand the surface and apply a full flood coat for a seamless chess or checkers board finish.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Ghost Molds for Resin | 4 Styles | Ghost 3D Molds, Halloween Mold

(0)

From $19.99

SMALL ROUNDED GHOST: 1 3/4" Tall by 1 1/2" Wide
LARGE ROUNDED GHOST: 2 1/2" Tall by 2" Wide
TALL GHOST: 3" Tall by 1" wide
SHORT GHOST: 1 3/4" Tall by 1 1/4" Wide

This listing is for Ghost Molds for Resin. These are available in 3 styles. All ghosts have the eyes etched in them. These ghosts are a perfect addition to your Halloween decor.

The New Rounded Ghosts do not have a split. The Tall Ghost also does not have a split. (It used to but not any more :) They are easy to demold.

The Short ghost mold come presplit for easy demolding of your resin piece. Use the rubber band provided to aid in sealing the split before pouring.

Please message us with any questions you may have regarding this mold.

Resin work: @Artworkbyjennyshlemon

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Pot Leaf Mold | 1.875” x 1.875” x .25” | Weed Mold, Keychain Mold, Magnet Mold

(0)

$16.00

Tealight Candle Holder Mold, Tea Light Holder Mold

(0)

$44.00

Round Keychain Mold | 1.25”, 1.5”, 1.75”, 2” | Circle Mold, Magnet Mold, Earring Mold

(1)

From $14.00

FINAL CAST DIMENSIONS:

Small: 1 1/4"
Medium: 1 1/2"
Large: 1 3/4"
Extra Large: 2"
DEPTH: 1/4"

This listing is for a Round Circle Mold. This can be also used as a Round Keychain Mold, Circle Grip Mold, Earrings Mold or Magnet Mold. Each mold comes with 6 cavities allowing you to create more at a time. The size and shape of the 1.75" circle is perfect to fit over any phone grip. This allows you to customize the phone grip to your liking!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Deep Pill Tray Mold

(0)

$75.00

Final Cast Dimensions:

Length: 7.5"
Width: 4.5"
Rim Width: 1/2"
Rim Height: 1/2"
Base Height: 1"
Overall Height: 1.5"
All Edges Rounded

This listing is for a Deep Pill Tray Mold. All edges of this tray will be rounded giving it a softer look. You will have up to 1" of working room underneath the face of the tray. This gives you plenty of room for your florals or any other inclusion you would like to add. Our Deep Pill Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!! There will be no lines in your finished product.

Resin Work and Photos by @kanetahale

Free Layout Template Included

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

12" Round x 1.25" Romeo & Juliet Serving Board Set Silicone Mold - Nesting Serving Board Mold

(0)

From $25.00

Final Cast Dimensions:
Each half is approximately 13" x 6"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Round Romeo & Juliet Serving Board Set Silicone Mold. This one mold will produce 2 pieces which will nest together perfectly.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Round Ornament Mold, Donut Ornament Mold, 3/4" Deep,

(0)

$25.00

Heart Keychain Mold | 1.75"x1.75"x.25" | Hair Clip Mold, Magnet Mold

(0)

$16.00

Angel Silicone Mold | 2 Sizes - 6" & 9" |

(0)

From $45.00

Cancer Awareness Ribbon Mold | 13" x 8" x 1.25" | Cancer Ribbon Mold, Ribbon Mold

(0)

$85.00

9”x 6”x 2” Deep Cross Silicone Mold | 2 Shapes |

(0)

$95.00

4" x 6" Picture Frame Silicone Mold | 1.5" Deep |

(0)

From $5.00

FINAL CAST DIMENSIONS:

Photo Size: 4" x 6"
Outer Dimension: 7" x 9"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume: 67.5 in ^3 (inches cubed)

This listing is for a Picture Frame Mold. This mold is designed so you are working with your flowers face up.

*** 1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order. ***

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage.

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Resin work and photos courtesy of @aafloralpreservation

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

13"x 11.5"x 1.25" Heart Charcuterie Board Silicone Mold - Serving Board Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 13"
Width: 11.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a heart shaped serving board silicone mold that has an integrated heart shaped handle hole.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Comb Mold | 7"x 2" | Hair Comb Mold

(1)

$19.99

Sign Molds for Resin | 7"x3" or 5"x2" | Wall Hanging Mold, Hanging Sign Mold

(0)

From $20.00

Alphabet Mold | 2” Tall | Numbers Mold | Full Reverse | Uppercase Alphabet Mold, Keychain Mold

(0)

From $50.00

5" x 7" Picture Frame Silicone Mold | 1.5" Deep |

(0)

From $5.00

FINAL CAST DIMENSIONS:

Photo Size: 5" x 7"
Outer Dimension: 8" x 10"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume: 67.5 in ^3 (inches cubed)

This mold is designed so you are working with your flowers face up.

*** 1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order. ***

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage.

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Resin work and photos are courtesy of @aafloralpreservation

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

17" X 17.5" x 1.25" Romeo & Juliet Nesting Serving Board Set Silicone Mold - Nesting Charcuterie Mold

(1)

From $25.00

Final Cast Dimensions:

Size Together: 17" X 17.5" X 1.25"

Tall Half: 17" x 9"

Short Half: 13.5" x 8.5"

Depth: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Romeo & Juliet Serving Board Set Silicone Mold. This one mold will produce 2 pieces which will nest together perfectly.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Star Tray Silicone Mold | Sizes - 5", 7", 9" |

(0)

From $38.00

Pen Blank Silicone Mold | 6"x1"x1" |

(0)

$75.00

Geode Tray Mold | Sizes - 4"x6", 6"x8", 9"x13" | Rectangle Tray Mold,

(0)

From $30.00

Deep Paw Print Tray Mold

(0)

$95.00

Final Cast Dimensions:

Length: 7"
Width: 7"
Rim Width: 1/2"
Rim Height: 1/2"
Base Height: 1"
Overall Height: 1.5"
All Edges Rounded
Glossy Finish

This listing is for a mold to create a Deep Paw Print tray. This mold could work well as a remembrance mold of a favorite pet. It offers room for a collar, pet tag or fur.

All edges of this tray are rounded giving it a softer look. You will have up to 1" of working room underneath the face of the tray. Our Deep Paw Print Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Out!! There will be no lines in your finished product. Free Layout Template Included.

Resin work and photo credit goes @mlcresindesigns

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Hexagon Silicone Mold | 9 SIZES |

(0)

From $75.00

Deep Standing Round Mold | 5", 7", 9" |

(0)

From $75.00

Deep Gem Silicone Mold | 5", 6", 8" |

(0)

From $45.00

17"x 4"x 1.25" Beer Bottle Cheese Board Silicone Mold - Board Mold, Bottle Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 17"
Width: 4"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Beer Bottle Board Silicone Mold. So many options with this mold. It can be used as a cheese board or also as wall decor.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Shell Tray Silicone Mold | 9”x 9” |

(0)

$60.00

Pot Leaf Tray Mold | Sizes - 5.5", 8", 10" | Weed Tray Mold

(0)

From $29.99

FINAL CAST DIMENSION

Sizes: 5.5", 8", 10"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

This listing is for a Pot Leaf Tray Mold. This Leaf Tray Mold comes in 3 sizes. Small is 5.5", Medium is 8" and Large is 10" It is approximately 5/8" deep. The base is 1/4" thick and the walls are 3/8" thick.
Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Organizer Tray Mold | 6" x 8" | Divided Tray Mold

(0)

$59.99

Football Tray Silicone Mold | 11” x 7” |

(0)

$71.00

Baseball Mold | 9" |Sports Mold, Baseball Tray Mold

(0)

$64.99

18"x 5"x 1.25" Wine Bottle Shaped Charcuterie Board Silicone Mold, Cheese Board Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 18"
Width: 5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a wine bottle shaped charcuterie mold or cheese board mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Paw Print Tray Silicone Mold | 7”x 7” | Dog Paw Print Mold, Cat Paw Print Mold

(0)

$66.00

Gingerbread Man Coaster Mold, Christmas Mold

(0)

$27.50

Deep Arch Mold | 7 Sizes |

(0)

From $105.00

12"x 6.5"x 1.25" Beer Can Cheese Board Silicone Mold - Board Mold, Soda Can Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 12"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Beer Can Board Silicone Mold. So many options with this mold. It can be used as a cheese board or also as wall decor.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Triangle Tray Silicone Mold | Sizes - 4", 6", 8" |

(0)

From $39.99

Peace Sign Tray Silicone Mold | 5" |

(0)

$44.00

Moon Tray Silicone Mold | Sizes - 6"x8", 8"x10" |

(0)

From $44.00

Corner Tray Silicone Mold, Triangle Mold, Bathroom Tray Mold

(0)

$49.00

Mushroom Mold | 2” x 2” x .25”| Keychain Mold, Magnet Mold

(0)

$16.00

Geode Keychain Mold | 1.75” | Magnet Mold, Earring Mold

(1)

$16.00

Deep Butterfly Silicone Mold | 2 Sizes | Butterfly Mold, Memorial Mold

(0)

From $95.00

Mitten Coaster Set Mold

(0)

$27.50

Santa Coaster Set Mold, Christmas Coaster Mold

(0)

$27.50

Christmas Coaster Molds, Gift Box Coaster Mold, Christmas Mold

(0)

$27.50

Deep Standing Oval Mold | 2 Styles |

(0)

$150.00

Deep Standing Heart Mold | 6" & 8" |

(0)

From $60.00

Deep ROUNDED Bookend Mold | 3 Sizes |

(0)

From $175.00

Deep Rainbow Mold | 2 Sizes |

(0)

From $110.00

Deep Heart Mold | 5", 7", 9" |

(0)

From $60.00

Deep Bookend Mold | 3 Sizes |

(0)

From $175.00

6" Tall Alphabet Letter Silicone Molds

(0)

$75.00

9" Tall - 3" Deep Alphabet Letter Silicone Molds

(0)

From $130.00

FLORAL PRESERVATION MOLDS

FINAL CAST DIMENSIONS:
Height: 9"
Width: Varies on each individual letter
Depth: 3"
Surface Finish: Smooth/Shiny/Glossy

LETTERS "F" AND "P" HAVE BEEN REVISED SO THAT THEY STAND ON THEIR OWN.

With our letter molds, you are able to work with your flowers face up.

*WALL STIFFENERS* are embedded into the silicone to make sure the silicone does not bow inwards or outwards. All MAIN straight sides of the letters will have embedded supports. For example: "A" will only come with stiffeners on the two long outside walls. "B" will only have it along the long straight wall on the left. "C" will have none due to it being curved, etc...

Resin work and photos by @ivorycoledesigns
Listing video by @flower_preserve

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

6" x 6" Picture Frame Mold | 1.5" Thick |

(0)

From $5.00

FINAL CAST DIMENSIONS:

Photo Size: 6" x 6"
Outer Dimension: 9" x 9"
Border Width: 1.5"
Thickness: 1.5"

Approximate Resin Volume 1.5 thick Molds: 67.5 in ^3 (inches cubed)

This mold is designed so you are working with your flowers face up.

1 Piece of Acrylic Photo Backing is included with every mold order. Additional pieces available to order.

Acrylic backing may need to be slightly sanded in order to fit due to resin shrinkage.

Photo placement is recessed 3/4” from the top.

Minimum pour depth for proper function is 1" - 1.25”

You may wonder how a picture will be able to stay in and you will quickly see that in each corner a ledge is formed. Having the ledge in the corner allows for easy demolding. On top of this, you will be able to purchase precision cut acrylic sheets that fit the photo perfectly. This is how the photo will sit in your resin piece on the ledges without bending. The picture will set halfway up the frame. You can double sided tape the photo to the acrylic and also glue or tape the acrylic to the resin to make it secure. You can also sandwich the picture between 2 pieces of acrylic.

Free Template included for easy layout of your design!!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Resin work and photos are courtesy of @aafloralpreservation

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

17"x 6.5"x 1.25" Fishtail Cheese Board Silicone Mold - Charcuterie Board Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 17"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Fishtail Charcuterie Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

14.6" x 12"x 1.25" Teardrop Charcuterie Board Silicone Mold - Serving Board Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 14.6"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Teardrop Charcuterie Board Silicone Mold. This mold has an embedded round handle hole at the top of the teardrop.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

14"x 8.25"x 1.25" Genie Cheese Board Silicone Mold - Charcuterie Board Mold

(0)

From $25.00

Final Cast Dimensions:
Tall: 14"
Width: 8.25"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Genie Charcuterie Board Silicone Mold or Cheese Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.