Coaster Molds

FINAL CAST DIMENSIONS
Size: Approx. 4"
Depth: 1/2"

We are offering this in 7 shapes: Round, Square, 4 unique Geode shapes and Hexagon. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Diameter: Daisy 1 - 6 1/2"
Daisy 2 - 5 1/2"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

This listing is for a silicone mold to create a Daisy tray. This tray comes with 2 options. DAISY1 has non symmetrical petals which means the petals are of a slightly different size/shape.  DAISY2 has symmetrical petals meaning all the petals are exactly the same. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height of all Shapes: 3.5". 

Width: Varies according to shape

Depth: 1.25"

Finish: Glossy

SHAPES AVAILABLE:
Arch
Book Ends
Heart
Hexagon
Rainbow
Rectangle
Square
Standing Oval
Standing Round

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Small Pill Tray: 4" x 6"
Large Pill Tray: 4" x 9"
Small Oval Tray: 4" x 6"
Large Oval Tray: 6" x 8"
Small Rectangle Tray: 4" x 6"
Large Rectangle Tray: 6" x 8"
Small Circle Tray: 5"
Large Circle Tray: 7"

Rim Height: 3/8"
Rim Width: 3/8"
Rim Base: 3/8"
Overall Height: 3/4"
All Edges Rounded

Surface Finish:  Smooth and Glossy

This listing is for our Improved Tray Molds.  We've taken the shapes that you love and made them even better. All edges of this tray will be rounded giving it a softer look.  It offers a thicker base of 3/8" plus a slightly increased rim width. This gives you extra room to work with.  These Tray Molds will produce a product that is smooth and glossy on all sides!! Inside and Outside!!  There will be no lines in your finished product from stacking acrylic.   This is an ULTRA QUALITY MOLD!

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.  

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 5.5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a shiny silicone mold to create a Tree shaped Coaster Set with a stand! This set comes with 4 Tree Coaster molds and an Oval tray stand for when you want to display your coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Shamrock shaped Coaster Set with a stand! This set comes with 4 Shamrock coaster molds and an Oval tray stand for when you want to display your coasters. This comes in 2 molds. One for the 4 coasters and one for the stand.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Diameter: 5" - 7" - 9"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Scalloped Tray Mold.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4"
Width: 5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a shiny silicone mold to create a Weed Leaf Coaster Set with a stand. This set comes with 4 Weed Leaf Cavities in 1 mold and an oval tray stand with slots for when you want to display or are not using your coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Snowflake Coaster Set with a stand! This set comes with 4 snowflake molds and an Oval tray stand for when you want to display your coasters. The snowflakes come in two different styles so all four aren't the same.

The image on this tray is engraved which means it will come out matte. The image will also be recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Diameter: 4"
Thickness: 1"

Resin work done by @resinforareason

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 4.5”

Width: 4.5”

Depth: 1/4”

This listing is for a Star Coaster Molds. This Coaster Set Mold comes with 4 Star molds and an Oval tray stand for when you want to display your coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured.  Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message  and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS:

Height: 3.5"

Width" 2"

Depth: .25"

Surface Finish:  Smooth/Glossy

This listing is for a Small Rectangle Mold that can be used to make name tags, mini signs, magnets, or keychains! Each Rectangle Mold comes with 6 cavities allowing you to create more at a time.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Length: 4"
Width: 4"
Thickness: 1"
Sharp Corners
Glossy/Smooth/Shiny Top + Sides

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message  and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 
Small: 5”x5”
Medium: 7”x7”
Large: 9”x9”
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Star Tray Silicone Mold. The Star Mold comes in three sizes.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 4.75"
Width: 2.75"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Butterfly Coaster Mold! This set comes with 4 Butterfly molds. This set does come with a stand to display the coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 
Football: 11" x 7"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Football Mold. 

The image on this tray is engraved which means it will come out matte. The image will also be slightly recessed into your resin piece upon de-molding.


Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4.5"
Width: 4.5"
Deep: .25"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Spider Web Coaster Set Mold with a stand! This set comes with 4 Spider web molds and an oval tray stand for when you want to display your coasters. 

The image on the coaster is engraved which means it will come out matte. The image will also be recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 5"
Width: 5"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Ghost Coaster Mold Set with a stand (AKA Ghosters)! This set comes with 4 ghost molds and an oval tray stand with slots for when you want to display or are not using your coasters. The ghosts come in two different styles so all four aren't the same. 

The image on this coaster is engraved which means it will come out matte. Which is the 2 eyes and mouth on the ghost. The image will also be recessed into your resin piece upon de-molding which will allow you to paint it or leave it be.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 5.5"
Width: 4"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a Coaster Mold Set to create a Coffin Coaster Set with a stand. This Coffin Mold comes with 4 identical coffins in one mold and an oval tray stand with slots for when you want to display or are not using your coasters. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 4 1/8"
Width: 4 5/8"
Deep: 1/4"
Surface Finish: Smooth/Shiny/Glossy

This listing is for a silicone mold to create a Heart Coaster Set with a stand! This set comes with 4 Heart coaster molds and an Oval tray stand for when you want to display your coasters. This comes in 2 molds. One for the 4 coasters and one for the stand.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Length: 6.5"
Width: 6.5"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a silicone mold to create a corner tray. This tray will perfectly fit any corner. This is a great decor piece for your bathroom or really any where. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

This listing is for a silicone mold to create a Mushroom Coaster Set! This set comes with a 4 cavity Mushroom molds. This set does not come with a stand to display the coasters.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS

Small: 4"x4"
Medium: 6"x6" 
Large: 8"x8"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"

This listing is for a silicone mold to create a Square tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Small: 5”x4”

Medium: 7”x5”

Large: 9”x7”
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a silicone mold to create an Egg shaped  tray. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of
alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Length: 9"
Width:9"
Rim Height: 3/8"
Base Height: 1/4"
Overall Height: 5/8"


This listing is for a Spiderweb Tray Mold  

The image on this tray is engraved which means it will come out matte. The image will also be slightly recessed into your resin piece upon de-molding.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal)

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS 

Height: 1.75”

Width: 1.75”

Depth: .25”

This listing is for a silicone mold to create a Pentagon shape used for phone grips, magnets or keychains.  Each mold comes with 6 cavities allowing you to create more at a time.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping. 

Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• Plastic Wrap/Bag Marks on trays will go away within 48-72 hours.
• All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

FINAL CAST DIMENSIONS
Height: 4"
Width: 4.75"
Depth: 1"

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

All molds are handmade and inspected before shipping.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.
SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message on Etsy and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.