Molds with Handles

Final Cast Dimensions:
Length: 18"

Width: 7.4"

Depth: 1.25"

Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Cleaver Shaped Cheese Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Length: 22"
Width: 6"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Large Bowed Rectangle Silicone Mold. This style has double handle holes. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 15"
Width: 11"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for an Oval Charcuterie Board Silicone Mold with dual embedded handles.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Chunky Bowed Rectangle with dual handles Charcuterie Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 17"
Width: 7"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Charcuterie Board Mold with an organic handle.

Resin work and photos courtesy of @tuzzstable

his listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Size Together: 17" X 14" X 1.25"

Tall Half: 17" x 6.5"

Short Half: 14.6" x 7.5"

Depth: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Romeo & Juliet Serving Board Set Silicone Mold that has a cutout heart in the center of it. This one mold will produce 2 pieces which will nest together perfectly. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Diameter: 12"
Length with Handle: 15.5"

Depth: 1.25"

Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Deep Charcuterie Board Mold. 

Resin work and photo courtesy of @bupp_woodworks and @rockpaperesin

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting. 

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please shoot me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 18"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Rectangle with Embedded Dual Handles Charcuterie Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:

Size Together: 17" X 17.5" X 1.25"

Tall Half: 17" x 9"

Short Half: 13.5" x 8.5"

Depth: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Romeo & Juliet Serving Board Set Silicone Mold. This one mold will produce 2 pieces which will nest together perfectly. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This style charcuterie board mold has a free flow handle.

Listing video and photo courtesy of @jaredcoreyconcepts

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 12"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Round Cheese Board Silicone Mold with 1 Integrated Handle. This would make a great Serving Tray too.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Each half is approximately 13" x 6"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Round Romeo & Juliet Serving Board Set Silicone Mold. This one mold will produce 2 pieces which will nest together perfectly. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 16"
Width: 7"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Charcuterie Board Mold. This style has the flared handle and a rectangle shaped body. 

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Height: 18"
Width: 8"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Slanted Rectangle Charcuterie Board Mold with 1 embedded handle.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 17"
Width: 6.5"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Fishtail Charcuterie Board Silicone Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 14.6"
Width: 12"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Teardrop Charcuterie Board Silicone Mold. This mold has an embedded round handle hole at the top of the teardrop.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.

Final Cast Dimensions:
Tall: 14"
Width: 8.25"
Deep: 1.25"
Surface Finish: Smooth/Shiny/Glossy

Acrylic Template: Exact size of final casting

Final Cut Template: 1/8" undersized to trim excess resin.

This listing is for a Genie Charcuterie Board Silicone Mold or Cheese Board Mold.

This listing features an optional precision laser-cut acrylic router template, designed to be the simplest, most accurate, and repeatable solution for shaping wood or wood-resin pieces into charcuterie boards, serving trays, handles, functional art, and more.

These versatile templates allow you to either trace the pattern for rough-cutting or use them directly with a flush trim router bit for clean, precise shaping. It's an essential woodworking tool that streamlines your workflow, reducing production time while maintaining accuracy and consistency.

The final cut template allows you to take your casting out of the mold and flush trim any resin that seeped around the wood. This speeds up production time and reduces post sanding work.

We suggest using mold release to extend the life of your silicone mold. It is not needed, it is recommended. We suggest Ease Release 200. Please note that mold release does affect the surface finish by removing the glossy surface on the mold. It will make the mold surface finish satin/matte which directly transfers to your casting.

Please message us with any questions you may have regarding this mold.

**Please note this listing is for the silicone mold ONLY.

Our silicone molds cure to a strong platinum rubber which is tear resistant and exhibits very low long-term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys.

SILICONE MOLD CARE INSTRUCTIONS

• DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast.
• Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles.
• USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin.
• Make sure the resin is fully cured. Uncured resin may rip the mold.
• Please follow all safety precautions when using resin. It is very toxic.
• If you have further questions or concerns about your mold, please send me a message and I’ll get you taken care of.

PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.